CCMDB.accdb

The CCMDB.mdb is an MS Access database, with the name being the acronynm for Critical Care Medicine Database. CCMDB.mdb screens the data for internal consistency and ranges, and then exports it for further processing during sending.

Updating of CCMDB.mdb

Rolling out new versions of ccmdb.mdb is done by Tina or Trish using a batch file called updt_all.bat. A ccmdb.mdb file that is currently open WILL NOT be overwritten. See the update Log for information about changes, and see Requested Changes for changes planned for the future.

Data in the CCMDB.mdb

Any data in the ccmdb.mdb is considered transient, the file can be replaced with an empty new version at any time On the laptops, the data listed by CCMDB.mdb is actually stored in c:\ccmdb_data\ccmdb.mdb, so the front end ccmdb can still be replaced at any time

Data in

The PDAs sync into CCMDB.mdb. At locations that use laptops only, data is entered manually.

Data out

in a format that can be imported into TMSX or MedTMS.

File Locations

PDA

Each PDA has a combo of two Access databases associated to it:

ccmdb.mdb file which is identical for all until synced into

settings.mdb which contains location specific information such as the path to the Regional Server, and the hospital and ward names.

Additionally, this program folder contains a \Master directory where the master version of the ccmdb.mdb is stored. Any changes required to the program can be made on the master file, and then rolled out by copying the master\updt_all.bat batch file to a local drive (batch code can’t cope with running from an unnamed drive) and running it.

Laptop

see Laptop Setup

Form Sizes

The form sizes on the laptops are continuously being tweaked to accomodate, especially, any of the laptops we use. The form size was increased to accommodate the screens on the laptops which are small but have a high native resolution.

X out of Program

• We find that if you are in the program and you have enlarged the view box, and then you "X" out, it closes out the program, not just take you back to the start up page of "edit patients" etc. But if you are in the view box and you are in smaller screen and "X" out, it doesn't close the program it goes to the start up screen "edit patients". Which is what we want.Are we doing something wrong? gogogirl 14:33, 3 June 2009 (CDT)
  • There should be two Xs at the top right corner. The top one closes the entire application, the bottom one only that screen. If you use the door button instead in the patient view form then there should be no confusion. I don't think this has changed between the regular app and this one, has it? Ttenbergen 13:25, 9 June 2009 (CDT)

Yellows that don't go away when the value is fixed

Sometimes the fields for values that appear to be correct are still highlighted in yellow.

If this happens, try putting a checkmark into the complete box corresponding to that tab. This will re-run the checks.

Also, if the error box at the bottom seems to have out-of-date info in it, click the "Reset Err" button.

This problem happens because some changes in data will affect multiple boxes (e.g. survive and discharge-to) and running all checks after every change would slow down the program further.

Object With Variable Error

Occasionally the following error comes up

Microsoft Office Access
Object variable of With block variable not set - Patient <number>
OK

This error occurs when the program has previously run into a different problem and is still "confused". If this happens, go back to the Main Form (i.e. exit out of the patient viewer) and click the "reset" button.

CCMDB.mdb password

The password for the ccmdb.mdb is known as "the tasty password". If you don't know it, and need to know it, talk to Trish or any data collector. All data collectors need to be thoughtful as to who they give this password out to.

The CCMDB.mdb is using the same password everywhere. This is required at all PDA locations because synchinc depends on it. Once the PDAs are phased out we might be able to customize passwords.

Synching

See Syncing the PDA

Sending Patients

See Sending Patients

Master File

see Master files for the data collection process

Deleting data on PDA after sending from access

What is the process everyone should follow before deleting sent patients from the PDA? Some people check with Pagasa, some check on the regional server that data has actually been posted. Is it a common occurrence for data not to have been posted? Ttenbergen 22:32, 4 May 2009 (CDT) Template:Discussion

• go to regional server Output folder.

Check Vic folder go to recent batch #.CSV check files, scroll to ensure all files present. say no to save if you change anything. Delete completed profiles off PDA. gogogirl 16:19, 18 March 2009 (CDT)

• After closing access I click on output, then your unit open up the info and check. eg the number of completes, admits, comorbs, etc. I then delete my completes on my PDA--PStein 08:36, 18 March 2009 (CDT)

• After sending you check your output by opening twister and clicking on output, then find your site and click on the batch number csv you just sent. Your sent files should appear, scroll across and make sure the areas that have to have information in them ie. admit date and time etc. are filled in. If everything looks OK close out and you can deiete your completed files. Lois -- LBilesky 14:47, 17 March 2009 (CDT)